Power only reefer moves put an outside tractor and driver under your refrigerated trailer. That sounds simple until you realize the trailer, the reefer unit, the fuel tank, and the temperature setting all belong to you, while the truck pulling them belongs to someone else. If nobody decides in advance who sets the temperature, who fuels the unit, and who answers a high-temp alarm at 2 a.m., the load is at risk before it leaves the dock.
This guide is for shippers, food distributors, and private fleets that own or lease reefer trailers and need extra tractor capacity. It covers how power only trucking works with temperature-controlled equipment, what federal food-transport rules expect from each party, and a pre-dispatch checklist you can use before you tender the load. If you are new to the model, start at the Power Only Truck homepage first.
What makes a power only reefer load different
With a standard refrigerated full truckload, the carrier supplies the trailer and its refrigeration unit, so the carrier usually owns the equipment questions. With a power only reefer move, the carrier supplies the power unit and driver only. Everything behind the fifth wheel—box, insulation, doors, reefer unit, sensors—is shipper-controlled equipment. That shift changes three things:
- Equipment condition is on the trailer owner. A unit that will not hold setpoint is a trailer problem, not a tractor problem.
- Temperature instructions must travel with the load. The driver cannot guess the setpoint or the run mode (continuous vs. cycle) for your product.
- Monitoring and alarm response need an owner. If your trailer has telematics, decide whether your team or the carrier watches it and who calls whom.
The rest of the power only basics still apply. Your trailer still has to couple safely—see our fifth wheel hitch checklist for power only moves—and you still need trailer interchange coverage sorted out before an outside carrier takes custody of a trailer you own.
What the FDA Sanitary Transportation rule expects
If you are shipping human or animal food by motor vehicle in the U.S., the FDA’s FSMA rule on Sanitary Transportation of Human and Animal Food likely applies. FDA describes it as setting requirements for shippers, loaders, carriers, and receivers covering vehicles and equipment, transportation operations, training, and records. It also lists exemptions, such as businesses under $500,000 in average annual revenue and food completely enclosed by a container—except food that requires temperature control for safety. Check those exemptions with your own compliance team; this guide is not legal advice.
Shipper duties: write down the operating temperature
Under 21 CFR 1.908, a shipper of food that requires temperature control for safety must specify in writing to the carrier an operating temperature for the transportation operation, including the pre-cooling phase if necessary. Shippers must also develop written procedures to make sure the food moves under adequate temperature control. The same section lets any covered party reassign its responsibilities to another covered party in a written agreement. For power only, that written agreement is where you settle who handles the reefer unit.
Carrier duties depend on the written agreement
Section 1.908(e) applies carrier duties when the carrier and shipper agree in writing that the carrier is responsible, in whole or in part, for sanitary conditions. Those duties can include providing the shipper’s operating temperature to the receiver on request and showing that temperature was maintained—for example, with ambient readings at loading and unloading, or time/temperature data from the trip. The pre-cooling duty in that section is written for a carrier that offers equipment with a refrigeration unit. In a power only move, you are usually the one offering the trailer, so plan on handling pre-cooling yourself unless your agreement says otherwise.
Equipment must be able to hold temperature
21 CFR 1.906 requires that vehicles and equipment used for food needing temperature control be designed, maintained, and equipped as necessary to provide adequate temperature control, and be kept in sanitary condition. Because the trailer is yours, the maintenance history of the reefer unit and the condition of the box are yours to document.
One more rule applies no matter what the trailer is carrying: under 49 CFR 392.7, a driver must be satisfied that brakes and trailer brake connections, lights, tires, wheels, and coupling devices are in good working order before driving. A reefer that is cold but has a flat tire or dead marker lights will still get refused.

Who handles what: power only reefer vs. carrier-supplied reefer
Use this table as a starting point for your rate confirmation or written agreement. Every line can be reassigned in writing; the point is that each one has a named owner.
| Task | Carrier-supplied reefer (typical) | Power only reefer (typical) |
|---|---|---|
| Reefer unit maintenance and repair | Carrier | Shipper / trailer owner |
| Writing down the operating temperature | Shipper | Shipper |
| Pre-cooling the trailer before loading | Carrier offering the equipment | Shipper, unless agreed otherwise |
| Fueling the reefer unit before dispatch | Carrier | Shipper; agree in writing if the driver may fuel en route and how it is billed |
| Washout / sanitary condition of the box | Carrier | Shipper / trailer owner |
| Watching temperature during transit | Carrier | Whoever the agreement names (shipper telematics or driver checks) |
| Temperature records on request | Carrier, if responsible under the agreement | Whoever owns the reefer data |
| Brakes, lights, tires, coupling pre-trip | Carrier driver | Carrier driver inspects; shipper keeps trailer roadworthy |
Pre-dispatch checklist for a power only reefer load
Walk through this list before you tender the load. It pairs well with our general shipper checklist.
1) Paperwork and instructions
- Written operating temperature (and pre-cool target, if needed) on the bill of lading or load instructions.
- Run mode noted: continuous or start/stop cycle, per your product requirements.
- Who to call on a temperature alarm, with a 24/7 phone number.
- Written agreement that names who is responsible for temperature monitoring and records.
- Trailer number, reefer unit number, and seal number matched to the tender.
2) Reefer unit readiness
- Unit pre-cooled to the specified temperature before loading begins.
- Fuel level checked and recorded; fueling plan agreed for long lanes.
- No active alarm codes; recent service documented.
- Telematics or data logger active, if you use one, and someone assigned to watch it.
3) Box and doors
- Interior clean, dry, and free of odors or residue from a prior load.
- Door seals intact; doors close and latch tight.
- Air chute and airflow path not blocked by product stacked to the ceiling or against the front wall.
4) Roadworthiness for the outside driver
- Tires, lights, brakes, and air lines in working order (the items 49 CFR 392.7 tells drivers to check).
- Kingpin, upper coupler, and landing gear ready for a clean hook.
- Trailer registration and any required inspection paperwork in the nose box or available to the driver.

Drop and hook vs. live load with reefers
Drop and hook works well for power only reefer programs because your team can pre-cool and load on its own schedule, and the outside tractor just swaps trailers. The trade-off is that a loaded reefer sitting in a yard is burning fuel and depends on the unit running unattended. If you pre-load, set a rule for how long a loaded reefer can wait and who checks it.
Live loading cuts yard dwell but ties the tractor to your dock schedule. If you go live, have the trailer pre-cooled before the truck arrives so loading is not waiting on the reefer to pull down.
Empty reefer repositioning
Not every reefer move is loaded. Seasonal demand often leaves refrigerated trailers in the wrong place, and power only is a common way to rebalance them. For empty moves, tell the carrier whether the unit should be off, on standby, or running (for example, to arrive pre-cooled), and confirm who pays for any fuel. Our empty trailer moves page covers the logistics side of repositioning.
Common power only reefer mistakes
- Setpoint given verbally only. The FDA rule expects the operating temperature in writing. Put it on the paperwork.
- Reefer tank low at dispatch. An outside driver may not know where your trailer can be fueled or who pays.
- No one watching the alarms. Telematics only help if someone acts on them.
- Assuming the driver fixes the unit. A power only carrier provides a tractor and driver, not reefer repair. Line up a mobile service vendor for your trailer brand along the lane.
- Roadworthiness skipped because the box is cold. Tires, lights, and brakes still decide whether the hook happens.
When power only makes sense for refrigerated freight
Power only reefer tends to fit when you already own or lease temperature-controlled trailers and need tractors for peak season, a new lane, or relief for your private fleet. It is usually a poor fit if you do not have reliable reefer maintenance or someone available to own temperature monitoring. Compare it against carrier-supplied trailers in our power only vs. full truckload guide, and see how we run shipper-owned vans in dry van power only trucking.
Get a power only reefer quote
Power Only Truck is a Logi Transports LLC site based in Sebastian, FL (MC-1636889, USDOT 4230991). Our contracted drivers provide tractor capacity for shipper-owned trailers, reefers included. When you request a quote, include origin and destination, trailer type and length, operating temperature, loaded or empty, pickup window, and who handles reefer fuel and monitoring. Here is how to get a power only quote fast.
Request a power only reefer quote · Call (864) 791-5644 · Email quotes@logitransports.com


Leave a Reply